C MR-L1
RGB LED Lighting Controller
with remote
Contrôleur d’éclairage LED RGB avec télécommande
Controlador de iluminación LED RGB con control remoto
RGB LED-Beleuchtungssteuerung mit Fernbedienung
Dispositivo di controllo illuminazione LED RGB con telecomando
©2021 Clarion Marine Audio
RGB LED Lighting Controller
with remote
Contrôleur d’éclairage LED RGB avec télécommande
Controlador de iluminación LED RGB con control remoto
RGB LED-Beleuchtungssteuerung mit Fernbedienung
Dispositivo di controllo illuminazione LED RGB con telecomando
©2021 Clarion Marine Audio
General Connections
NOTES
• Install in a dry, well-ventilated location; do not install in an engine compartment
or other areas of extreme heat. Do not install where it will be directly exposed
to the elements.
• To optimize performance, avoid confined installation locations or areas
surrounded by metal; maintain at least 25 cm (10 in) of separation from any audio
signal cables.
• Make sure the total amperage demands of all connected LED circuits does not
exceed the output capacity of the controller.
• *Install a fuse (not included) at the main +12V power wire (Red) connection point
that is appropriate for the total current draw of all LED circuits (up to 10 A).
• For short-circuit protection, we recommend installing a fuse (not included)
at EACH speaker’s +12V LED connection lead. Refer to your speaker’s LED
specifications for individual fuse values.
NOTES
• Install in a dry, well-ventilated location; do not install in an engine compartment
or other areas of extreme heat. Do not install where it will be directly exposed
to the elements.
• To optimize performance, avoid confined installation locations or areas
surrounded by metal; maintain at least 25 cm (10 in) of separation from any audio
signal cables.
• Make sure the total amperage demands of all connected LED circuits does not
exceed the output capacity of the controller.
• *Install a fuse (not included) at the main +12V power wire (Red) connection point
that is appropriate for the total current draw of all LED circuits (up to 10 A).
• For short-circuit protection, we recommend installing a fuse (not included)
at EACH speaker’s +12V LED connection lead. Refer to your speaker’s LED
specifications for individual fuse values.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits of Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Control Function
Power: On/Off
Demo Mode: On/Off
Dynamic Mode: Select from 20 modes
Dynamic Speed: Select from 10 levels
Fixed Color: Select from 20 colors
Brightness: Select from 8 levels
Preset Color: Select from 7 colors
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions,
compliance with exposure requirements.
This equipment has been tested and found to comply with the limits of Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Control Function
Power: On/Off
Demo Mode: On/Off
Dynamic Mode: Select from 20 modes
Dynamic Speed: Select from 10 levels
Fixed Color: Select from 20 colors
Brightness: Select from 8 levels
Preset Color: Select from 7 colors
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions,
compliance with exposure requirements.